Torna al blog
Guide pratiche 2026-11-16 REGULATION 7 visualizzazioni

Rubber Zip Mitts: How to Wear Made-to-Order Bondage Mitts

Rubber Zip Mitts: How to Wear Made-to-Order Bondage Mitts

A practical guide to sizing, putting on, and caring for REGULATION's made-to-order 0.8mm latex zip mitts, with honest notes on what the catalog does and does not confirm.

Start with the two measurements that matter

The Rubber Zip Mitts are made from heavy 0.8mm latex and use a zip entry to restrict exploring fingers during bondage. Because this is the Made to Order version, the most useful first step is not choosing a colour but checking your wrist and fist measurements against the two sizes the catalog lists.

The catalog gives two size rows: S/M fits an 18.5cm wrist and 25cm fist, while L/XL fits a 20.5cm wrist and 29cm fist. Measure around your wrist and around your closed fist, then compare both numbers. If one measurement sits at the edge of a size, the catalog does not provide a half-size or custom-fit option, so treat that as a fit decision rather than a guarantee.

What the catalog confirms about the mitts

  • Rubber Zip Mitts // Made to Order: Made from heavy 0.8mm latex with a form-fitting panelled construction. The material and panel build affect how the mitts feel and how much care they need, so this is worth knowing before you order.
    Rubber Zip Mitts // Made to Order
    Rubber Zip Mitts // Made to Order
  • Rubber Zip Mitts // Made to Order: Zip-entry design intended to restrict exploring fingers during bondage. This explains the core function: the zip is the entry point, and the restriction is the point of the product.
  • Rubber Zip Mitts // Made to Order: Un-padded construction. There is no padding layer, so the fit and the feel come directly from the latex and the panel seams.
  • Rubber Zip Mitts // Made to Order: S/M: 18.5cm around wrist, 25cm around fist. L/XL: 20.5cm around wrist, 29cm around fist. These are the only sizing figures supplied, so they are the basis for choosing a size.

A supported way to put them on

The catalog describes zip entry and a form-fitting panel construction, but it does not supply a dressing sequence, lubricant recommendation, or specific fastening instructions. The steps below stick to what the product record supports and leave out procedural details the record does not confirm.

  1. Check the size against both measurements: Confirm your wrist and fist measurements against the S/M or L/XL row before the mitts are made. This is the only sizing guidance the catalog provides.
  2. Open the zip entry fully: The mitts are zip-entry, so start with the zip open and the entry clear before sliding your hand in.
  3. Seat the hand and close the zip: The panelled construction is form-fitting, so let the mitt settle around the hand rather than forcing it. Close the zip once the hand is seated.
  4. Check comfort at the wrist: The catalog does not specify a tightness setting or a locking mechanism, so stop if the wrist edge feels uncomfortable and adjust before continuing.

Locking zip restraints: what the record does and does not confirm

The product name and description refer to zip-entry mitts and to restricting fingers, but the supplied record does not confirm a lock, a locking slider, or any specific locking hardware. If locking is part of your plan, confirm the closure type with the store before ordering rather than assuming the zip itself locks.

The same caution applies to any claim that the mitts are escape-proof or tamper-proof. The catalog describes restriction of exploring fingers, not a locking security rating. Treat the mitts as a bondage accessory with a zip entry, and build your session around that confirmed function.

Made to order means a wait, and a colour choice

This is the Made to Order version, and the catalog notes a wide range of colours is available. It also points readers to a Ready To Ship version if they would rather not wait. That is the honest trade-off: more colour choice and a made-to-order timeline versus faster availability from the ready-to-ship listing.

The catalog does not list a production time, so ask the store about the current lead time if timing matters. It also does not confirm which specific colours are in stock at any moment, so confirm your colour choice when you order.

Care for 0.8mm latex mitts

The catalog confirms the material is heavy 0.8mm latex but does not supply a cleaning product, drying method, or storage instruction. Rather than invent a routine, follow the latex care guidance REGULATION publishes for its other rubber items and keep the mitts away from anything that could damage the latex.

Because the mitts are un-padded and panelled, pay attention to the seams and the zip area when you clean and store them. The record does not confirm whether the zip is metal or plastic, so check the closure yourself and avoid anything that could corrode or snag it.

Safety checkpoints before and during wear

These checkpoints follow from the confirmed product facts. They are not a substitute for your own risk assessment or for the store's instructions.

  • Agree on a stop signal first: The mitts restrict finger use, so agree on a verbal or physical signal before the zip is closed.
  • Keep the wrist edge comfortable: The catalog does not specify a maximum wear time or a tightness limit. Check in regularly and remove the mitts if the wrist feels uncomfortable.
  • Do not assume the zip locks: The record does not confirm locking hardware, so do not rely on the mitts as a locking restraint unless the store confirms it.
  • Check the latex before each use: Inspect the panels and the zip entry for damage. The catalog does not provide a replacement schedule, so use your own judgement.

Who these mitts suit, and what to confirm first

The Rubber Zip Mitts suit someone who wants a form-fitting, un-padded latex mitt that restricts finger use during bondage and who is happy to wait for a made-to-order colour. They are less suited to anyone who needs a confirmed locking closure or a padding layer, because the supplied record does not confirm either.

Before ordering, confirm three things with the store: the current made-to-order lead time, the colour options available, and the exact closure type. That keeps your expectations aligned with what the catalog actually confirms.

Articoli correlati

Customer Service
Home
Prodotti
Carrello
Profilo